Surrey Kickout Flashing Leaks: Signs, Causes and Repair
Surrey Kickout Flashing Leaks: Signs, Causes and Repair
A kickout flashing leak is a roof-edge problem that shows up in the wall. Where a sloped roof ends against a wall, a small bent piece of metal or moulded plastic is supposed to throw the runoff into the gutter. When it is missing, too small or poorly sealed, that water runs down behind your siding instead, and in Surrey’s long wet season it can soak sheathing and framing before you see a single drip indoors. The fix is to open the junction, repair what is damaged, and rebuild the flashing so it ties into both the roof and the wall layers. That is work for a roofer who handles the whole junction, which is what we do for Surrey homes, townhouse complexes and small commercial buildings through our residential roof repair and inspection service.
TL;DR
- Kickout flashing is the diverter at the bottom end of a roof-to-wall junction. It sends roof runoff into the gutter instead of behind the cladding.
- A missing or badly sealed kickout often shows only as a vertical stain or streak on the siding below the roof edge, and serious damage can sit hidden with little to see.
- Newer cladding such as fibre-cement, vinyl and brick veneer can hide water entry for years.
- A proper repair means exposing the junction, fixing damaged sheathing or framing, and re-integrating the flashing with the wall and roof layers. A caulk bead on the outside is not that.
- Strata councils and property managers should check every roof-to-wall eave on a complex in the same inspection, because the same detail repeats on every unit.
Table of Contents
- What kickout flashing does at a Surrey roof-to-wall junction
- Why kickouts leak
- Signs you may have a kickout leak
- A quick look you can do safely from the ground
- How a proper repair works
- What this means for strata corporations and property managers
- When to repair the flashing and when to look at the whole roof
- Our view on kickout flashing
- Getting the junction inspected
- FAQ
- Sources
What kickout flashing does at a Surrey roof-to-wall junction
Picture a two-storey home with a lower roof that runs into the side of an upper wall. Along that wall, shingles are protected by step flashing, small L-shaped metal pieces laid in layers, each one overlapping the one below. They keep water from getting behind the wall where the roof meets it.
At the bottom of that run, the roof ends but the wall keeps going. All the water that has been sliding down the roof beside the wall arrives at one point. The kickout is the angled piece that catches it and turns it out. The U.S. Department of Energy’s building science education material describes it as a diverter at the eave end of the roof-wall junction that channels runoff into the gutter and keeps it from running behind the cladding. The International Code Council’s water management guide says the same thing in practical terms: it is used where the roof stops but the wall continues, and it moves water off the step flashing plane and away from the wall.
A note on sources: these are U.S. guides, because they are the clearest published explanations of the detail. The physics of water running down a roof edge is the same in Surrey, and the problem is arguably sharper here, where rain is frequent from autumn through spring and walls rarely get a long dry spell to recover.
Why kickouts leak
A kickout can fail in four ordinary ways.
It was never installed. On many older homes and some newer builds, the step flashing simply stops at the end of the wall. The ICC guide warns that without one, concentrated roof runoff spills behind the cladding.
It is too small. The Department of Energy’s education page notes that site-made diverters may be undersized or have unsealed seams, and it favours seamless moulded plastic or welded-seam metal pieces. A kickout that is a few centimetres short lets water shoot past it during a heavy downpour.
It is not tied into the wall layers. The Building America Solution Center says an undersized diverter, or one poorly integrated with the water-resistive barrier and cladding, can direct water into the wall cavity, damaging sheathing, framing and insulation and potentially causing mould. The ICC adds that an improperly folded or unsealed bottom seam can send water into the wall as well.
The gutter beneath it cannot cope. Roof-wall intersections concentrate runoff, and the same Solution Center page notes that this flow can overflow gutters during heavy storms. A perfect kickout feeding a clogged or undersized gutter still dumps water on the wall. We cover the wider pattern in our guide to why roof flashing fails in Surrey.
Signs you may have a kickout leak
This is the awkward part: the leak is often invisible from the inside for a long time. Look for these, ideally during or just after a rainstorm.
- A vertical streak or stain on the siding directly below where the roof edge meets the wall. InterNACHI, the home inspectors’ association, says vertical wall stains can be visible evidence of water penetration, but that severe concealed damage can exist with little or no visible evidence.
- Dark streaks and an overflowing gutter at that corner. Water pouring over the gutter lip at the wall end is a sign the runoff is not being captured.
- Peeling paint or swollen, soft trim on older wood siding. The Solution Center points out that this is the easier case, because fibre-cement, vinyl and brick-veneer claddings may hide water intrusion for years.
- A wall that continues past the lower roof edge and gutter. InterNACHI names this layout as the classic place where roof water misses the gutter, gets behind siding and becomes trapped in the wall.
- Interior signs on the other side of that wall: a stain on the ceiling corner, bubbling paint, a musty smell in a closet or a soft spot in baseboard.
A caution on telling this apart from other leaks: a stain near a roof-to-wall corner can also come from a chimney, a skylight, a window above or the gutter itself. The pattern that points to a kickout is water marks that begin at the eave end of the wall and run downward, rather than spreading outward from a window or penetration. If you are not sure, an inspection that follows the water upstream is quicker than guessing. Our roof leak detection guide explains how leaks get traced.
A quick look you can do safely from the ground
You do not need a ladder, and you should not use one on a wet roof edge.
- Find every spot where a roof meets a higher wall. Walk the property and note each lower roof that stops against a wall.
- Look at the bottom end of each run. You are looking for a small angled metal or plastic piece sitting over the gutter end. If you see only siding and a gutter, the kickout may be missing.
- Check the siding directly below. Streaks, stains, mould, peeling paint or warped trim are all worth noting. Take photos.
- Watch it in rain. If water sheets over the gutter at that corner or runs down the wall, the detail is not working.
- Photograph and call. Roof edges above a first storey are not a place for a homeowner to climb, so stop here and book an inspection.
How a proper repair works
It is tempting to run a bead of sealant along the siding and hope. Sealant weathers, and it does nothing about water that is already behind the cladding. The U.S. Department of Energy’s guidance for existing homes lays out a better sequence, and it matches how a careful repair goes:
- Check the wall beside the eave. The guide advises checking for deterioration when the original detail lacked a kickout.
- Open it up. When flashing is absent, damaged or leaking, the guide recommends removing the siding and flashing to expose the junction and inspecting the roof and wall framing.
- Repair what is damaged. Rotten sheathing or framing is replaced before anything new goes on.
- Rebuild the layers. The same guide calls for integrating new adhesive membrane and step or continuous flashing with both the roof and wall weather-resistant layers, then fitting the kickout at the eave so it sends water toward a gutter.
- Lap everything shingle-fashion. The Solution Center says flashing layers should be integrated in shingle fashion, upper layers overlapping lower ones, so nothing drains behind them. The ICC guide says the wall drainage plane should lap over the top of the step flashing, so water lands on the shingles.
Brick and stone veneer need extra detail
If the wall is brick or stone veneer, the step flashing alone is not enough. The ICC guide says through-wall flashing must be added to the step flashing, or a flexible membrane used to connect the wall drainage plane to the roof, because exterior-face step flashing alone does not return water to the roof. Many Surrey homes have a veneer base with siding above, so ask whoever quotes the work how they will handle that transition.
Why the gutter gets fixed at the same visit
Because the kickout hands its water to the gutter, the two are one system. Checking the gutter slope, outlet and downspout during the same visit costs little extra effort and prevents the repair from being undone by an overflow next November.
What this means for strata corporations and property managers
On a townhouse complex, the roof-to-wall detail is repeated dozens of times, often built by the same crew from the same drawings. If one unit has a missing kickout, others probably do too. Water damage that stays hidden for years is the worst kind of surprise in a depreciation report or a special levy discussion.
A sensible approach is to inspect every roof-to-wall eave in one pass, photograph each one, record which have kickouts and which show staining, and group the repairs into one scope rather than reacting unit by unit. Fixing a dozen junctions in one mobilization is easier to plan and to explain to owners than a dozen emergency calls. Our strata and multifamily roofing services cover repairs, maintenance and reroofing, and the Surrey strata repair and maintenance page is a good starting point for council members.
Small commercial buildings with a sloped roof section that meets a taller wall have the same exposure. Our commercial roofing services page lists what we handle for those owners.
When to repair the flashing and when to look at the whole roof
A kickout repair is a good fit when the roof covering is in decent shape and the problem is confined to one or two junctions. If the shingles are near the end of their life, the better move is often to fix the junction as part of a reroof, so that new step flashing, membrane and kickouts are installed together with the new covering. That way the wall layers and the roof layers are lapped in the correct order from the start. On cedar roofs that are being converted, the junctions are rebuilt anyway, which is why they deserve attention in that project. See our cedar-to-asphalt conversion page for that route.
Whichever route you take, the sequence of work matters more than the product: expose, repair, re-integrate, then divert.
Our view on kickout flashing
We think of a kickout as a small part that carries a big job. It sits at the lowest point of a long run of roof, and everything above it depends on it working.
What we focus on is the whole junction: the wall layers, the step flashing, the kickout and the gutter it feeds. Our approach is built around city-specific expertise in Surrey and Metro Vancouver conditions, and our licensed, insured crews look at how water will actually travel across a roof in a wet Lower Mainland winter, not only at the one spot that is stained.
If you have a streak below a roof edge, or you are a strata council with a row of similar townhomes, we would rather walk the junctions with you early than see you open a wall later.
Harman
Getting the junction inspected
If you have spotted any of the signs above, we can inspect the roof-to-wall junctions, the gutters and the surrounding cladding, and tell you what is happening and what a repair involves. Homeowners can start with our residential roofing services. If water is coming in right now, our emergency roof repair service is listed on our main page.
For a broader look at what else commonly goes wrong on Surrey roofs, the flashing section of our Surrey roof repair guide is a useful companion.
FAQ
Is kickout flashing required in Surrey?
The 2024 BC Building Code took effect on March 8, 2024, and a municipal bulletin summarizing its changes does not list a change specific to kickout flashing. Whatever the minimum, water management at a roof-to-wall eave is good practice, and it is how we approach every junction we repair or build.
Can I just caulk the gap where the wall meets the gutter?
Caulk is not a substitute for a diverter. It does not turn the water away from the wall, and it does nothing for moisture already trapped behind the siding. The repair guidance calls for exposing the junction, fixing damaged materials and re-integrating the flashing with the wall and roof layers.
How long can a kickout leak go unnoticed?
Potentially for years. The Building America Solution Center notes that fibre-cement, vinyl and brick-veneer cladding can conceal water intrusion for long periods, and InterNACHI says severe damage can exist with little visible evidence. Regular checks of siding below roof edges are worthwhile for that reason.
Does the same issue affect townhouses and commercial buildings?
Yes. Any place where a sloped roof ends against a wall that carries on above it has the same water-management challenge. On strata complexes the detail repeats, so one inspection pass across all units is the efficient way to find out which ones need work.
Sources
- Kick-out Flashing at Roof-Wall Intersections, U.S. Department of Energy Building Science Education
- Step and Kick-Out Flashing at Roof-Wall Intersections, Building America Solution Center
- Flashing of Roof-Wall Intersections in Existing Homes, Building America Solution Center
- Water Management Details: Housewraps, Flashings, Windows, ICC
- Kickout Flashing, InterNACHI
- Bulletin: 2024 BC Building Code Changes
Recommended
Our Roofing Blog
Have more questions about roofing?
Check out our FAQs or give us a call today to speak to an expert roofer in Vancouver Lower Mainland, BC. We're here to help our neighbours make educated decisions about their roof. For our team, we value helping clients save money while making their roofs last.




